|
|
| Line 18: |
Line 18: |
| | *[[SS7]] | | *[[SS7]] |
| | *[[Administration]] | | *[[Administration]] |
| − |
| |
| − | == '''Carrier Setup''' ==
| |
| − |
| |
| − |
| |
| − |
| |
| − | The following steps are required to setup a new carrier
| |
| − |
| |
| − |
| |
| − | 1. Decide on the type of signaling that will be used and configure it. (Click on the links for more information on configuration, manuals etc.)
| |
| − | The following are supported:
| |
| − | a) [[SS7 - ITU/ANSI ISUP]]
| |
| − | b) [[ISDN]]
| |
| − | c) SIP/SIP-T
| |
| − |
| |
| − | 2. For E1/T1 connections, Sky Dance uses IP gateways to convert the PSTN signaling to SIP.
| |
| − |
| |
| − | :Skynet offers the following fully integrated gateways
| |
| − |
| |
| − | :For SS7 to SIP/SIP-T based on hardware from the following vendors:
| |
| − | :: a) [[Audiocodes Manuals|<u>Audiocodes Mediant</u>]] series gateways (Mediant 2000 - Mediant 8000)
| |
| − | :: b) Sangoma A10x series cards.
| |
| − |
| |
| − | :For ISDN to SIP
| |
| − | :: a) Based on Audiocodes Mediant series gateways (Mediant 2000-Mediant 8000)
| |
| − | :: b) Sangoma A10x series based cards.
| |
| − |
| |
| − | 3. To configure a SS7 Carrier using Audiocodes gateways, there are several steps extra steps as follows:
| |
| − | a. [[Physical layer configuration|<u>Configure the physical layer</u>]] of the links and voice channels on the gateway. This is done via the Audiocodes element management system (EMS) or the Web GUI (M3K only).
| |
| − | b. [[Configure the originating point code|<u>Next the E1/T1 originating point code</u>]], [[Configure SS7 links|<u>links</u>]], [[Configure the linksets|<u>linksets</u>]] and [[Configure SS7 routes |<u>routes</u>]] must be configured via the EMS or Web GUI.
| |
| − | c. [[SS7#SS7_Stack|<u>Configure the originating point code</u>]], [[SS7#SS7_Linkset|<u>links</u>]], [[SS7#SS7_Linkset|<u>linksets</u>]] and [[SS7#SS7_Route|<u>routes</u>]] setup must be duplicated using the Sky Dance GUI. This will allow Sky Dance to control the gateway using M3UA and MGCP.
| |
| − |
| |
| − | 4. These steps are commont to SIP and SS7 Carriers
| |
| − | a. Setup the [[Translations#Partitions|<u>partition</u>]] for that carrier or reuse an existing one.
| |
| − | b. Setup [[Translations#Calling_Pre_Translation|<u>pretranslation</u>]] and/or [[Translations#Calling_Post_Translation|<u>postranslation</u>]] for the calling number if required.
| |
| − | c. Setup the [[Translations#Called_Pre_Translation|<u>pretranslation</u>]] and/or [[Translations#Called_Post_Translation|<u>postranslation</u>]] for the called number if required.
| |
| − | d. Setup an [[System#SIP_Proxy|<u>inbound proxy</u>]] if this is an inbound carrier or an System#SIP_Proxy|<u>outbound proxy</u>]] if this is an outbound carrier.
| |
| − | e. Setup the [[System#SIP_B2BUA|<u>B2BUA</u>]] which will handle the call.
| |
| − | f. For outbound carriers setup the [[Gateway_List|<u>gateway list</u> with the IP addresses of the terminating carrier's gateway(s).
| |
| − | g. [[Resource Groups|<u>Add Resource groups</u>]] for the voice circuits in the Sky Dance GUI.
| |
| − | h. Setup [[Routes|<u>route lists</u>]].
| |
| − | i. Setup [[Translations|<u>translations</u>]] and routing.
| |
| − |
| |
| − | 5. For SS7 Carriers this is the final step
| |
| − | a. [[SS7#SS7_CIC_Mapping|<u>Configure the voice circuits</u>]] to map the CICs to the resource group(s) just created.
| |
