Difference between revisions of "SS7 - ITU/ANSI ISUP"
Jump to navigation
Jump to search
| (18 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| + | '''[[Sky Dance Web User Interface |Back]]''' | ||
| + | |||
Click the following links to download manuals for or links to the configuration of the following hardware: These manuals have detail on how to configure the physical spans and setup SS7 links | Click the following links to download manuals for or links to the configuration of the following hardware: These manuals have detail on how to configure the physical spans and setup SS7 links | ||
| Line 8: | Line 10: | ||
{{pdf|LTRT-91403_Rev_001_Media_Gateway_Programmer's_User_Manual_v2.1.22.pdfâ |M8K Programmers User Manual}} | {{pdf|LTRT-91403_Rev_001_Media_Gateway_Programmer's_User_Manual_v2.1.22.pdfâ |M8K Programmers User Manual}} | ||
| − | To configure SS7 for Audiocodes gateways, there are several steps: | + | 4. To configure SS7 for Audiocodes gateways, there are several steps: |
| − | 1. Physical layer configuration of the links and voice channels on the gateway is done via the Audiocodes element management system (EMS) or the Web GUI (M3K only). | + | 1. [[Physical layer configuration|<u>Physical layer configuration</u>]] of the links and voice channels on the gateway is done via the Audiocodes element management system (EMS) or the Web GUI (M3K only). |
| − | 2. | + | 2. [[Configure the originating point code|<u>Next the E1/T1 originating point code</u>]], [[Configure SS7 links|<u>links</u>]], [[Configure the linksets|<u>linksets</u>]] and [[Configure SS7 routes |<u>routes</u>]] must be configured via the EMS or Web GUI. |
| − | 3. | + | 3. Then [[SS7#SS7_Stack|<u>the originating point code</u>]], [[SS7#SS7_Linkset|<u>links</u>]], [[SS7#SS7_Linkset|<u>linksets</u>]] and [[SS7#SS7_Route|<u>routes</u>]] setup must be duplicated using the Sky Dance GUI. This will allow Sky Dance to control the gateway using M3UA and MGCP. |
| − | + | 4. [[Resource Groups|<u>Resource groups</u>]] for the voice circuits must be created in the Sky Dance GUI. | |
| − | + | 5. Finally the voice circuits must be [[SS7#SS7_CIC_Mapping|<u>configured and assigned</u>]] to the resource group(s) just created. | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | + | Backend configuration of the Sky Dance Sangoma based SS7 GW is discussed in detail at the following links: | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | + | c) [http://wiki.sangoma.com/wanpipe-api-freetdm-mtp2api-configuration Sangoma SS7 configuration] | |
| − | + | d) [[SS7 Command line commands for Sky Dance Sangoma based SS7 GW]] | |
Latest revision as of 16:36, 21 January 2014
Click the following links to download manuals for or links to the configuration of the following hardware: These manuals have detail on how to configure the physical spans and setup SS7 links
a) Audiocodes Mediant 3000
http://www.sky-networks.com/mediawiki/images/1/11/Pdf_icon_32.png M3K EMS Manual http://www.sky-networks.com/mediawiki/images/d/da/Info_circle.png
http://www.sky-networks.com/mediawiki/images/1/11/Pdf_icon_32.png M3K MGCP/MEGACO Manual http://www.sky-networks.com/mediawiki/images/d/da/Info_circle.png
http://www.sky-networks.com/mediawiki/images/1/11/Pdf_icon_32.png M3K MGCP/MEGACO Product Reference Manual http://www.sky-networks.com/mediawiki/images/d/da/Info_circle.png
b) Audiocodes Mediant 8000
http://www.sky-networks.com/mediawiki/images/1/11/Pdf_icon_32.png M8K Programmers User Manual http://www.sky-networks.com/mediawiki/images/d/da/Info_circle.png
4. To configure SS7 for Audiocodes gateways, there are several steps:
1. Physical layer configuration of the links and voice channels on the gateway is done via the Audiocodes element management system (EMS) or the Web GUI (M3K only). 2. Next the E1/T1 originating point code, links, linksets and routes must be configured via the EMS or Web GUI. 3. Then the originating point code, links, linksets and routes setup must be duplicated using the Sky Dance GUI. This will allow Sky Dance to control the gateway using M3UA and MGCP. 4. Resource groups for the voice circuits must be created in the Sky Dance GUI. 5. Finally the voice circuits must be configured and assigned to the resource group(s) just created.
Backend configuration of the Sky Dance Sangoma based SS7 GW is discussed in detail at the following links:
c) Sangoma SS7 configuration d) SS7 Command line commands for Sky Dance Sangoma based SS7 GW
